FSM-80S is core-to-core alignment single fiber splicer succeeding
to FSM-60S. In addition to ruggedized concept, which 60S created,
the 80S has a series of new features, such as "Automated
wind-protector and tube-heater" for quicker splicing cycle as well
as fewer operation steps, "innovative carrying-case design" for
quicker preparation, "powerful Li-ion battey" for longer operation,
high resolution bigger LCD monitor, and "built-in operation
manuals" in various languages. Market is from backbone network
installation to opto-electronics components production for quality
SM (ITU-T G.652 & G.657), MM (ITU-T G.651), DS (ITU-T G.653),
NZDS (ITU-T G.655), Others
80 to 150μm
100 to 1000μm
Fibre cleaved length
5 to 16mm using Sheath Clamp A, B or 5 to13mm using FH-60-250,
Actual average splice loss
0.02dB with SM, 0.01dB with MM, 0.04dB with DS, 0.04dB with NZDS.
7sec:SM FAST mode, 12sec :SM AUTO mode, 15sec:AUTO mode
60dB or greater
100 splicer modes are available
Splice loss estimate
Several types of core deformations as well as core axis offset are
taken into account for accurate loss estimate.
Attenuation splice function
Intentional high splice loss of 0.1dB to 15dB (0.01dB step) can be
made for an
inline fixed attenuator
Storage of splice result
The last 2000 results to be stored in the internal memory.
X / Y (300X magnification), or both X and Y simultaneously (160X
By two CMOS cameras for intersecting fiber viewing and 4.73 inches
TFT colour LCD monitor
1.96 to 2.25N
0-5000m above sea level, 0-95% RH and -10 to 50°C respectively.
Built-in auto-start tube heater with 10 heating modes and up to 20
Tube heat time
13-15sec. with FP-03 protection sleeve. Total memory of 30 heating
modes are available
60mm, 40mm and a series of micro sleeves.
No. of splice/heating
200 times of splicing and heat shrinking under with BTR-09
Auto voltage selection from 100 to 240Va.c. or 10 to 15Vd.c. with
ADC-18. 14.8Vd.c. with BTR-09
USB2.0 ( Mini-B) for data and video signal transfer to PC.
Up to 15m/s wind velocity
146(W) x 159(D) x 150(H) mm
Including wind protector, monitor, and rubber protector
Excluding rubber foot
2.5 kg, with ADC-18 AC adaptor
2.7 kg, with BTR-09 battery
Our main products as below:
1. FUSION SPLICER: Sumitomo (Type-81C/39/-66/); Fujikura
(fsm-60S/60R); Fitel S178A; HSV-6000
2.OTDR: EXFO (FTB-1/AXS-110/AXS-100/ FTB-200/FTB-500); JDSU
3. POWER METER (PPM-350c, FPM-300, HSV300-P); LIGHT SOURCE
(FLS-300, HSV300-L); VFL (FLS-241, HSV-
321); Multi Loss tester (FOT-930, FOT-302)
4. Anritsu site master S331D, S331L, S331E,S332E.
5. Fiber cleaver (CT-30A/FC-6S), adapter, battery, electrode,
connector, fiber tool kits
6. Fiber cable, patch cord, adapter, closure, pigtail, optical
switch, patch panel, etc..
7.Maintainance and repair ,calibration service for the EXFO,
Sumitomo, Fujikura, Anritsu.
Be free to contact Jim if any questions
Jim's mobile: +8613728095480